Honda Civic manuals

Subaru Legacy BN/BS (2015-2019) Service Manual: Check list for interview check

Inspect the following items regarding the vehicle’s state.

Body Control System Check List for Interview Date of Vehicle Bring-in Year Month Day

Customer’s name

Registration No.

Initial year of registration

Year Month Date

Vehicle model

Frame number

Interviewer

Inspector

Engine type

Odometer reading

Customer specified content

Date and time when the trouble occurred

Frequency of trouble occurrence

Condition of trouble occurrence

Weather

Road conditions

Occurrence location

Accessory installation condition

Trouble condition

Diagnostic code

( )

1. CONDITION OF IGNITION POWER SUPPLY

Ignition position

OFF

ACC

ON (before starting engine)

START

ON (after starting engine, engine is running)

ON (after starting engine, engine is at a standstill)

Timing

Immediately after turning the ignition ON.

Immediately after turning the ignition to START.

2. SYMPTOMS

NOTE:

The items vary depending on destinations and equipment.

Vehicle condition

Clearance light does not illuminate.

Yes / No

Clearance light indicator does not illuminate.

Yes / No

Low beam does not illuminate.

Yes / No

High beam does not illuminate.

Yes / No

High beam indicator does not illuminate.

Yes / No

Front fog light does not illuminate.

Yes / No

Front fog light indicator does not illuminate.

Yes / No

Key cannot be removed from key cylinder.

Yes / No

Key can be removed with the shift in a range other than P.

Yes / No

Shift lever can not be operated.

Yes / No

Shift lock does not operate.

Yes / No

Warning buzzer for key left in ignition does not beep.

Yes / No

Immobilizer indicator does not illuminate.

Yes / No

Wiper deicer does not operate.

Yes / No

Rear defogger does not operate.

Yes / No

Combination meter does not dim when headlights are ON.

Yes / No

Rear wiper does not operate.

Yes / No

Doors can not be locked/unlocked with central door lock switch.

Yes / No

Doors and rear gate can not be locked/unlocked with keyless entry system or keyless access.

Yes / No

Trunk can not be opened with keyless entry system or keyless access.

Yes / No

Rear gate can not be opened when rear gate opener button is pressed.

Yes / No

Hazard answer-back does not operate.

Yes / No

Ignition key illumination does not light.

Yes / No

Ignition key illumination blinks.

Yes / No

Room light does not operate in accordance with door open/close operations.

Yes / No

Room light blinks.

Yes / No

Map light does not operate in accordance with door open/close operations.

Yes / No

Map light blinks.

Yes / No

Luggage/trunk room light does not operate in accordance with rear gate/trunk open/close operations.

Yes / No

Luggage/trunk room light is blinking.

Yes / No

Security monitoring does not start

Yes / No

Security cannot be cancelled

Yes / No

Hazard does not blink during security monitoring

Yes / No

Horn does not sound during security monitoring

Yes / No

Alarm operates as soon as security monitor condition occurs.

Yes / No

Security alarm does not operate even when impact is applied (model with impact sensor).

Yes / No

Engine does not start.

Yes / No

3. CONDITIONS UNDER WHICH TROUBLE OCCURS

Driving condition

At standstill (while idling)

When the vehicle is running

Vehicle speed km/h (MPH)

While accelerating

Acceleration km/h (MPH) to km/h (MPH)

Decelerating (with braking)

Deceleration km/h (MPH) to km/h (MPH)

Decelerating (without braking)

Deceleration km/h (MPH) to km/h (MPH)

Flat road

Uphill

Downhill

Gravel road

Bumpy road

Snowy road

Does it occur when operating any part-

Operated part:

TROUBLE SYMPTOM:

Are there any other troubles occurred-

From where:

TROUBLE SYMPTOM:

Basic diagnostic procedure procedure
CAUTION:• Subaru Select Monitor is required for reading DTC, performing diagnosis and reading current data.• Remove foreign matter (dust, water, oil, etc.) from the body integrated unit co ...

Clear memory mode operation
1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. ...

Other materials:

Disassembly
1. Place alignment marks on the shaft and outer race.2. Remove the PTJ boot band and boot.CAUTION:Be careful not to damage the boot.3. Remove the snap ring from PTJ outer race.4. Remove the PTJ outer race from shaft assembly.5. Wipe off grease.CAUTION:The grease is a special type of grease. Do not m ...

© 2017-2024 Copyright www.sulegacy.com