Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc b2286 engine speed signal(without auto start stop)

Subaru Legacy BN/BS (2015-2019) Service Manual / Keyless access with push button start system (diagnostics) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc b2286 engine speed signal(without auto start stop)

DTC DETECTING CONDITION:

When the engine speed signal transmitted from the ECM via solid line and the engine speed signal transmitted from the ECM via CAN communication line do not match.

TROUBLE SYMPTOM:

Cannot start the engine, or the engine stops after starting.

CAUTION:

For replacement procedure of keyless access CM, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

WIRING DIAGRAM:

NOTE:

For the coupling connector, refer to “WIRING SYSTEM”.

Keyless access with push button start system Keyless Access With Push Button Start System > WIRING DIAGRAM

STEP	CHECK	YES	NO
1.CHECK LAN SYSTEM. Inspect LAN system. Basic Diagnostic Procedure > PROCEDURE	Is LAN system normal-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2286 ENGINE SPEED SIGNAL(WITHOUT Auto Start Stop)	Perform the inspection according to the diagnosis for LAN system.
2.CHECK COMBINATION METER. Confirm that the speedometer is displayed normally.	Can the data be read normally-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2286 ENGINE SPEED SIGNAL(WITHOUT Auto Start Stop)	Perform the diagnosis for the engine. Diagnostics for Engine Starting Failure > PROCEDURE Diagnostics for Engine Starting Failure > PROCEDURE
3.CHECK CURRENT DATA. Check the current data display of «Keyless access with push button start» using Subaru Select Monitor. Read Current Data «Engine speed»	Can the data be read normally-	Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again. NOTE: In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2286 ENGINE SPEED SIGNAL(WITHOUT Auto Start Stop)
4.CHECK HARNESS (OPEN CIRCUIT). 1) Disconnect the keyless access CM connector. 2) Disconnect the ECM connector. 3) Using a tester, measure the resistance between the keyless access CM connector and ECM connector. Connector & terminal (i75) No. 7 — (B134) No. 10:	Is the resistance less than 1 --	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2286 ENGINE SPEED SIGNAL(WITHOUT Auto Start Stop)	Repair or replace the open circuit of harness.
5.CHECK HARNESS (GROUND SHORT CIRCUIT). Using a tester, measure the resistance between the keyless access CM connector and chassis ground. Connector & terminal (i75) No. 7 — Chassis ground:	Is the resistance 10 k- or more-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2286 ENGINE SPEED SIGNAL(WITHOUT Auto Start Stop)	Repair or replace the short circuit of the harness.
6.CHECK HARNESS. 1) Connect the keyless access CM connector and ECM connector. 2) Using the Subaru Select Monitor, measure the waveform between the keyless access CM connector and chassis ground. Connector & terminal (i75) No. 7 — Chassis ground:	Does the pulse stop when the engine is stopped, and does the pulse generate when the engine is started-	Replace the keyless access CM. Keyless Access CM	Perform the diagnosis for the engine. Diagnostics for Engine Starting Failure > PROCEDURE Diagnostics for Engine Starting Failure > PROCEDURE

Dtc b2779 remote control engine starter collation

DTC DETECTING CONDITION:When the keyless access CM does not respond to engine start even when the remote control engine starter is ON, or when there is a code mismatch.TROUBLE SYMPTOM:Remote engine st ...

Dtc b2285 steering lock position signal correlation

DTC DETECTING CONDITION:When the steering lock position signal transmitted from the steering lock CM via solid line and the steering lock position signal transmitted via LIN communication system do no ...

Other materials:

Dtc p2197 a/f / o2 sensor signal biased/stuck lean bank 2 sensor 1
DTC DETECTING CONDITION:Detected when two consecutive driving cycles with fault occur.CAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE.WIRING DIAGRAM:• Engine Electrical System ENGINE T ...