Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc c1423 different ecu specifications

Subaru Legacy BN/BS (2015-2019) Service Manual / Vehicle dynamics control (vdc) (diagnostics) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc c1423 different ecu specifications

DTC DETECTING CONDITION:

A fault is detected if the vehicle type information obtained from ECM via communication is different from the parameter setting information.

TROUBLE SYMPTOM:

• ABS does not operate.

• VDC does not operate.

• Hill hold does not function.

• EyeSight does not operate. (Models with EyeSight)

NOTE:

When parameter selection for VDCCM is improper, this DTC may be memorized.

STEP	CHECK	YES	NO
1.CHECK VDCCM&H/U IDENTIFICATION SYMBOL. Check the identification symbol attached on the H/U. General Description > SPECIFICATION	Is the identification symbol correct-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS	Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)
2.CHECK PARAMETER SELECTED IN VDCCM. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > MAINTENANCE MODE	Does the parameter registered in the VDCCM match the relevant vehicle-	CVT model: Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS MT model: Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS	Select and register the correct parameter. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > MAINTENANCE MODE
3.CHECK TCM SPECIFICATION. Check the TCM specification.	Is the specification of TCM same as vehicle specification-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS	Replace the TCM. Transmission Control Module (TCM) Transmission Control Module (TCM)
4.CHECK CVT SYSTEM. 1) Start the engine. 2) Check the DTC in CVT system. Read Diagnostic Trouble Code (DTC)	Is DTC of CVT system displayed-	Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS
5.CHECK ECM SPECIFICATION. Check the ECM specification.	Is the specification of ECM same as vehicle specification-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS	Replace the ECM. Engine Control Module (ECM) Engine Control Module (ECM)
6.CHECK ENGINE SYSTEM. 1) Start the engine. 2) Check DTCs of engine system. Read Diagnostic Trouble Code (DTC) Read Diagnostic Trouble Code (DTC)	Is engine system DTC displayed-	Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC) List of Diagnostic Trouble Code (DTC)	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS
7.CHECK VDCCM&H/U. 1) Perform the Clear Memory Mode. Clear Memory Mode 2) Perform the Inspection Mode. Inspection Mode 3) Read the DTC. Read Diagnostic Trouble Code (DTC)	Is the same DTC displayed-	Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS
8.CHECK DETECTION OF OTHER DTCS FOR VDC. Read Diagnostic Trouble Code (DTC)	Is any other DTC displayed-	Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)	Currently, it is normal. There may have been a poor contact in the harness and connector or a temporarily noise interference.

Dtc c1422 vdc interruption for engine convenience

DTC DETECTING CONDITION:A fault is detected if engine control prohibition flag from ECM is received.TROUBLE SYMPTOM:• VDC does not operate.• Hill hold does not function.NOTE:The warning li ...

Dtc c1741 pressure sensor

DTC DETECTING CONDITION:• A fault is detected if two fluid pressure signals in master cylinder are out of normal range.• A fault is detected if the condition that supply voltage for the fl ...

Other materials:

Caution
• Remove contamination including dirt and corrosion before removal, installation or disassembly.• Keep the disassembled parts in order and protect them from dust and dirt.• Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary removal, insta ...