Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc p0685 ecm/pcm power relay control circuit/open

Subaru Legacy BN/BS (2015-2019) Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0685 ecm/pcm power relay control circuit/open

DTC DETECTING CONDITION:

Detected when two consecutive driving cycles with fault occur.

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE.

WIRING DIAGRAM:

• Engine Electrical System ENGINE TYPE FB (WITHOUT PUSH BUTTON START) Engine Electrical System > WIRING DIAGRAM

• Engine Electrical System ENGINE TYPE FB (WITH PUSH BUTTON START) Engine Electrical System > WIRING DIAGRAM

STEP	CHECK	YES	NO
1.CHECK ECM CONNECTOR. Check the connecting condition of ECM connector.	Is the ECM connector correctly connected-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0685 ECM/PCM POWER RELAY CONTROL CIRCUIT/OPEN	Connect the ECM connector correctly.
2.CHECK HARNESS BETWEEN ECM AND MAIN RELAY CONNECTOR. 1) Turn the ignition switch to OFF. 2) Measure the voltage between ECM connector and engine ground. Connector & terminal (B134) No. 1 (+) — Engine ground (−): (B134) No. 14 (+) — Engine ground (−):	Is the voltage 10 V or more-	Repair the harness and connector. NOTE: In this case, repair the following item: • Short circuit to power supply in harness between ECM connector and main relay connector • Defective main relay	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0685 ECM/PCM POWER RELAY CONTROL CIRCUIT/OPEN
3.CHECK HARNESS BETWEEN ECM AND MAIN RELAY CONNECTOR. 1) Turn the ignition switch to OFF. 2) Remove the main relay. 3) Disconnect the connector from ECM. 4) Measure the resistance between the ECM connector and engine ground. Connector & terminal (B134) No. 60 — Engine ground:	Is the resistance 1 M- or more-	Repair the poor contact of ECM connector.	Repair the short circuit to ground in harness between ECM connector and main relay connector.

1. OUTLINE OF DIAGNOSIS

Detect the main relay stuck to ON.

Judge as NG when ECM keeps operating for more than predetermined time although the main relay does not turn to OFF after ignition switch is turned to OFF.

2. COMPONENT DESCRIPTION

The main relay controls current of coils by receiving instructions from the ignition switch and ELCM to switch ECM to ON/OFF.

3. EXECUTION CONDITION

Secondary Parameters	Execution condition
Main relay	OFF instruction

4. GENERAL DRIVING CYCLE

Perform the diagnosis only once when the enable conditions are established with the ignition switch OFF > ON.

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
ECM status	In operation

Time Needed for Diagnosis: 2500 ms

Malfunction Indicator Light Illumination: Illuminates when malfunction occurs in 2 continuous driving cycles.

Dtc p0700 transmission control system (mil request)

NOTE:For the diagnostic procedure, refer to AT section. Basic Diagnostic Procedure1. OUTLINE OF DIAGNOSISJudge as NG when there is CAN communication with the TCM and there is a MIL lighting request.2 ...

Dtc p062f internal control module eeprom error

NOTE:For the diagnostic procedure, refer to DTC P0606. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0606 CONTROL MODULE PROCESSOR1. OUTLINE OF DIAGNOSISJudge as NG when the EEPROM o ...

Other materials:

Removal
1. Disconnect the ground terminal from battery sensor. NOTE2. Lift up the vehicle.3. Remove the clips, and turn over the mud guard - front.4. Remove the fog light assembly - front.(1) Disconnect the connector.(2) Remove the screws and clips, and remove the fog light assembly - front.• Sedan m ...