Subaru Legacy BN/BS (2015-2019) Service Manual: Installation
1. SEAT BELT OUTER - REAR RH & LH (SEDAN MODEL) CAUTION: If the hook - rear seat is disconnected from the vehicle body, make sure to replace the hook - rear seat with a new part to prevent the decline of the fixed force of the seat.
1. Before installation, perform a unit inspection of retractor. Rear Seat Belt > INSPECTION 2. Install the seat belt outer - rear. CAUTION: • During installation, make sure that the seat belts are not twisted. • After installation, make sure that the seat belts are smoothly extended and wound. Tightening torque: Refer to “COMPONENT” of “General Description”. General Description > COMPONENT 3. Install the side pad assembly - backrest and the trim panel - rear pillar UPR. Tightening torque: Side pad assembly - backrest: 53 N·m (5.4 kgf-m, 39.1 ft-lb) 4. Install the rear seat cushion assembly. 5. Connect the ground terminal to battery sensor. NOTE 6. After installation, check the following points. • The seat belt is not twisted. • The seat belt can be pulled out and retracted smoothly. 2. SEAT BELT OUTER - REAR RH & LH (OUTBACK MODEL) CAUTION: If the hook - rear seat is disconnected from the vehicle body, make sure to replace the hook - rear seat with a new part to prevent the decline of the fixed force of the seat.
1. Before installation, perform a unit inspection of retractor. Rear Seat Belt > INSPECTION 2. Install the seat belt outer - rear. CAUTION: • During installation, make sure that the seat belts are not twisted. • After installation, make sure that the seat belts are smoothly extended and wound. Tightening torque: Refer to “COMPONENT” of “General Description”. General Description > COMPONENT 3. Install the trim panel - rear skirt and the trim panel - rear apron. 4. Install the mat - rear floor, spacer - rear floor, and sub trunk box. 5. Install the side pad assembly - backrest. Tightening torque: 53 N·m (5.4 kgf-m, 39.1 ft-lb) 6. Install the rear seat cushion assembly. 7. Connect the ground terminal to battery sensor. NOTE 8. After installation, check the following points. • The seat belt is not twisted. • The seat belt can be pulled out and retracted smoothly. 3. SEAT BELT - REAR SHOULDER CTR (SEDAN MODEL) CAUTION: If the hook - rear seat is disconnected from the vehicle body, make sure to replace the hook - rear seat with a new part to prevent the decline of the fixed force of the seat.
1. Install the retractor of seat belt - rear shoulder CTR. Tightening torque: Refer to “COMPONENT” of “General Description”.: General Description > COMPONENT 2. Install the trim panel assembly - rear shelf. 3. Install the high-mounted stop light. 4. Install the lower anchor of seat belt - rear shoulder CTR. CAUTION: • During installation, make sure that the seat belts are not twisted. • After installation, make sure that the seat belts are smoothly extended and wound. Tightening torque: 30 N·m (3.1 kgf-m, 22.1 ft-lb) 5. Install the side pad assembly - backrest and the trim panel - rear pillar UPR. Tightening torque: Side pad assembly - backrest: 53 N·m (5.4 kgf-m, 39.1 ft-lb) 6. Install the rear seat cushion assembly. 7. Connect the ground terminal to battery sensor. NOTE 8. After installation, check the following points. • The seat belt is not twisted. • The seat belt can be pulled out and retracted smoothly. 4. SEAT BELT - REAR SHOULDER CTR (OUTBACK MODEL) CAUTION: If the hook - rear seat is disconnected from the vehicle body, make sure to replace the hook - rear seat with a new part to prevent the decline of the fixed force of the seat.
1. Install the retractor of seat belt - rear shoulder CTR. Tightening torque: Refer to “COMPONENT” of “General Description”. General Description > COMPONENT 2. Install the trim panel - roof assembly. 3. Install the rear seat cushion assembly. 4. Connect the ground terminal to battery sensor. NOTE 5. After installation, check the following points. • The seat belt is not twisted. • The seat belt can be pulled out and retracted smoothly. 5. SEAT BELT - CTR RH AND LH CAUTION: If the hook - rear seat is disconnected from the vehicle body, make sure to replace the hook - rear seat with a new part to prevent the decline of the fixed force of the seat.
1. Install the seat belt - CTR RH/LH. Tightening torque: 30 N·m (3.1 kgf-m, 22.1 ft-lb) 2. Install the rear seat cushion assembly. 3. Connect the ground terminal to battery sensor. NOTE 4. After installation, check the following points. • The seat belt is not twisted. • The seat belt buckle is pulled out properly, and seat belt engagement can be performed smoothly. |
Inspection
1. VISUAL INSPECTIONCheck for the following, and replace with new parts if necessary.• Seat belt is slackened, bent or worn.• Seat belt is abnormally wound or extended.• Seat belt in ...
Other materials:
Dtc b2249 bluetooth module
DTC DETECTING CONDITION:• Detected when a connection between the Bluetooth module is lost (or there has already been no connection) and the connection cannot be established even after trying to reset the Bluetooth module hardware three times.• Detected when the connection with the Blueto ...
