Subaru Legacy BN/BS (2015-2019) Owners Manual: Menu screens

Pull and hold the " /SET" switch to enter the menu screens when all of the following conditions are satisfied.

•  The vehicle has been completely stopped.
•  The select lever is in the "P" position.
•  The menu screen entering screen is selected.

By operating the " " or " " switch on the steering wheel, you can select the menu.

Pull the " /SET" switch to enter the selected menu.

NOTE If you enter the "Go Back" menu, the system will return to the previous screen.

The menu list is as follows.

*1: The setting menu is available only for models with "keyless access with push-button start system".

*2: The setting can only be changed for the "keyless access" entry function. For details, refer to "Door unlock selection function" .

*3: For Outback only

Screen Settings

After entering the "Screen Settings" menu, select one of the following menus.

Welcome Screen

The welcome screen can be activated or deactivated. Select "On (with Sound)" to activate the screen and sound. Select "On (without Sound)" to activate the screen and deactivate the sound. Select "Off" to deactivate the screen.

Good-bye Screen

The Good-bye screen can be activated or deactivated. Select "On" to activate the screen. Select "Off" to deactivate the screen.

Gauge Initial Movement

The movement of the meter needles and gauge needles that occurs when the ignition switch is turned to the "ON" position can be activated or deactivated.

Select "On" to activate. Select "Off" to deactivate.

Gear Position Indicator Settings (MT models)

The gear position indicator light can be activated or deactivated. Select "On" to activate. Select "Off" to deactivate.

Units

You can select the displayed units of the distance, vehicle speed and volume.

Operate the " " or " " switch on the steering wheel to display the preferred units. Then pull the " /SET" switch to select the displayed units.

Languages

Operate the " " or " " switch on the steering wheel to display the preferred language. Then pull the " /SET" switch to select the displayed language.

Combination Meter Illumination (if equipped)After entering the "Combination Meter

Illumination" menu, select the following menu.

Meter Ring Illumination

The illumination of the combination meter rings can be activated or deactivated.

Select "On" to activate the illumination.

Select "Off" to deactivate the illumination.

EyeSight (models with EyeSight system)

NOTE For models with the EyeSight system, refer to the Owner's Manual supplement for the EyeSight system.

After entering the "EyeSight" menu, select one of the following menus.

Warning Volume

The volume of the warning buzzer that sounds when the EyeSight system is in use can be set in 3 stages ("Max", "Mid" and "Min").

Lead Vehicle Acquisition Sound

When adaptive cruise control is used, the buzzer that sounds under any of the following conditions can be activated or deactivated.

•  A vehicle is detected in front
•  Detection is not possible

Select "On" to activate the buzzer. Select "Off" to deactivate the buzzer.

Lead Vehicle Moving Monitor Function

When the lead vehicle moving monitor function is operated, the buzzer that sounds if a vehicle in front has started can be activated or deactivated. Select "On" to activate the buzzer. Select "Off" to deactivate the buzzer.

Vehicle Icon

The vehicle icon indication can be activated or deactivated. Select "On" to activate. Select "Off" to deactivate.

BSD/RCTA (if equipped)

After entering the "BSD/RCTA" menu, select the "Warning Volume" menu. You can set the volume of the warning buzzer for RCTA (Rear Cross Traffic Alert). You can select "Max", "Mid" or "Min".

RAB (if equipped)

After entering the "RAB" menu, select one of the following menus.

NOTE For models with RAB (Reverse Automatic Braking) system, refer to "Reverse Automatic Braking System"  63.

Warning Volume

The volume of the warning buzzer that sounds when the RAB (Reverse Automatic Braking) system is in operation can be set in 3 stages ("Max", "Mid" and "Min").

Sonar Audible Alarm

When the RAB (Reverse Automatic Braking) system is in operation, the buzzer that sounds if an obstacle is detected in the rear or if detection is not possible can be activated or deactivated. Select "On" to activate the buzzer. Select "Off" to deactivate the buzzer.

Vehicle Setting

After entering the "Vehicle Setting" menu, select one of the following menus

Keyless Entry System

After entering the "Keyless Entry System" menu, select one of the following menus.

•  Audible Signal (models with "keyless access with push-button start system"): The audible signal can be activated or deactivated. Select "On" to activate. Select "Off" to deactivate.
•  Hazard Warning Flasher (all models): The hazard warning flasher operation can be activated or deactivated. Select "On" to activate. Select "Off" to deactivate.
•  Driver Door Unlock (models with "keyless access with push-button start system"): The door unlock selection function is available for the "keyless access" entry function. For details, refer to "Door unlock selection function" . On this setting menu, the door unlock selection function for the driver's door can be customized.

  Select "Driver Door Only" to set as "Operational". Select "All" to set as "Nonoperational".

•  Rear Gate Unlock (Outback with "keyless access with push-button start system"): The door unlock selection function is available for the "keyless access" entry function. For details, refer to "Door unlock selection function" . On this setting menu, the door unlock selection function for the rear gate can be customized.

  Select "Rear Gate Only" to set as "Operational".

  Select "All" to set as "Non-operational".

Defogger

The defogger and deicer system can be set for the continuous operation mode or automatic shut-off mode. Select "Continuous" to select the continuous operation mode. Select "15 minutes" to select the automatic shut-off mode.

Interior Light

The setting for the period of time in which the interior lights remain on (OFF delay timer) after closing the doors and/or the rear gate can be set or customized. Select the preferred seconds to customize the operation period. Select "Off" to deactivate the OFF delay timer.

Auto Headlights

•  Light Sensitivity: The operational sensitivity of the auto on/ off headlights can be set. You can select "Max", "Mid", "Low" or "Min".
•  Wiper Link: The automatic headlight turn on function that is linked with the wiper operation can be activated or deactivated. Select "On" to activate. Select "Off" to deactivate.

Welcome Lighting

After entering the "Welcome Lighting" menu, select either of the following menus.

•  Approaching Time Set: The setting for the period of time in which the low beam headlights remain on when approaching the vehicle can be set or customized. Select the preferred seconds to customize the operation period. Select "Off" to deactivate the welcome lighting function when approaching.
•  Leaving Time Set: The setting for the period of time in which the low beam headlights remain on when exiting the vehicle can be set or customized.

  Select the preferred seconds to customize the operation period. Select "Off" to deactivate the welcome lighting function when exiting.

Default Settings

Select "Yes" to use the menu screen to restore customized settings to the factory default settings. Select "No" to return to the previous screen without restoring to the factory default settings.