Subaru Legacy BN/BS (2015-2019) Service Manual: Preparation tool

Subaru Legacy BN/BS (2015-2019) Service Manual / Mechanical(h6do) / General description / Preparation tool

1. SPECIAL TOOL

ILLUSTRATION	TOOL NUMBER	DESCRIPTION	REMARKS
	18250AA010	CYLINDER HEAD TABLE	• Used for replacing valve guides. • Used for removing and installing valve spring.
	18232AA000	ENGINE STAND	Used for disassembling and assembling engine.
	398744300	PISTON GUIDE	Used for installing piston in cylinder.
	18261AA010	VALVE OIL SEAL GUIDE	Used for press-fitting of intake valve guide oil seals and exhaust valve guide oil seals.
	18350AA000	CONNECTING ROD BUSHING REMOVER AND INSTALLER	Used for removing and installing connecting rod bushing.
	499977500	CAM SPROCKET WRENCH	Used for removing and installing cam sprocket.
	499587200	CRANKSHAFT OIL SEAL INSTALLER	• Used for installing crankshaft oil seal. • Used together with CRANKSHAFT OIL SEAL GUIDE (499597100).
	499597100	CRANKSHAFT OIL SEAL GUIDE	• Used for installing crankshaft oil seal. • Used together with CRANKSHAFT OIL SEAL INSTALLER (499587200).
	499718000	VALVE SPRING REMOVER	Used for removing and installing valve spring.
	499765700	VALVE GUIDE REMOVER	Used for removing valve guides.
	499765900	VALVE GUIDE REAMER	Used for reaming valve guides.
	18252AA000	CRANKSHAFT SOCKET	Used for rotating crankshaft.
	498277200	STOPPER SET	Used for preventing the torque converter from falling when removing and installing the engine.
	499585700	OIL SEAL GUIDE	Used for installing the chain cover oil seal.
	18251AA050	VALVE GUIDE ADJUSTER	Used for installing intake valve guides.
	18251AA060	VALVE GUIDE ADJUSTER	Used for installing exhaust valve guides.
	18355AA000	PULLEY WRENCH	• Used for removing and installing the crank pulley. • Used for removing and installing the idler sprocket. • Used together with PULLEY WRENCH PIN SET (18334AA000).
	18334AA000	PULLEY WRENCH PIN SET	• Used for removing and installing the crank pulley. • Used for removing and installing the idler sprocket. • Used together with PULLEY WRENCH (18355AA000).
	42099AE000	QUICK CONNECTOR RELEASE	Used for disconnecting the quick connector of the fuel delivery tube and FUEL HOSE (42075AG690). NOTE: FUEL HOSE (42075AG690) is used for checking the fuel pressure.
	18471AA000	FUEL PIPE ADAPTER	Used for inspecting the fuel pressure.
	42075AG690	FUEL HOSE	Used for inspecting the fuel pressure. NOTE: This is the SUBARU genuine part.
	18360AA020	HANGER	Used for removing and installing engine.
	— (Newly adopted tool)	SUBARU SELECT MONITOR 4	Used for setting of each function and troubleshooting for electrical system. NOTE: For detailed operation procedures of Subaru Select Monitor 4, refer to “Application help”.

2. GENERAL TOOL

TOOL NAME	REMARKS
Compression gauge	Used for inspecting compression pressure.
Timing light	Used for inspecting the ignition timing.
Vacuum gauge	Used for inspecting intake manifold vacuum.
Oil pressure gauge	Used for inspecting engine oil pressure.
Fuel pressure gauge	Used for inspecting fuel pressure.
TORX® socket (E12)	Used for removing and installing connecting rod cap.
Angle gauge	Used for angle tightening.
DST-i	Used together with Subaru Select Monitor 4.

Caution

• Prior to starting work, pay special attention to the following:1. Always wear work clothes, a work cap, and protective shoes. Additionally, wear a helmet, protective goggles, etc. if necessary ...

Component

1. V-BELT(1)V-belt(5)GeneratorTightening torque: N·m (kgf-m, ft-lb)(2)Collector cover bracket(6)Generator plateT1:20 (2.0, 14.8)(3)Tensioner ASSY(7)A/C compressor bracketT2: Generator > INSTALL ...

Other materials:

Installation
1. Pull out the key from the ignition switch, or turn the ignition switch to OFF.2. Close all the doors, trunk lid and rear gate.3. Press the UNLOCK button of the keyless transmitter or access key.4. Connect the ground terminal to battery sensor. NOTE5. Install the impact sensor.6. Change the setti ...