Subaru Legacy BN/BS (2015-2019) Service Manual: Registration body integrated unit operation
1. CONFIRM CURRENT SETTING 1. On «Start» display, select «Diagnosis». 2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed». 3. On «Main Menu» display, select «Each System». 4. On «Select System» display, select «Body Control» and then select «Enter». 5. On «Select Function» display, select «Customize». 6. Save the setting. Required items for new registration. (Except for system not equipped)
2. REGISTRATION BODY INTEGRATED UNIT (FUNCTION SETTING) CAUTION: For the body integrated unit, function selection is available to control the entire vehicle systems. It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment. If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item. • Be sure to correspond registrations, or User Customizing settings to vehicle equipment. • Do not change the settings of vehicle improperly. • Make sure that the key illumination does not blink with ignition switch ON, or that the body integrated unit registration item «Factory initial setting» is set to «Market». If “Factory initial setting” is set to «Factory», key illumination blinks when the ignition switch is turned ON, to notify that the settings are not confirmed. (If the vehicle is a model with the keyless access with push button start system, check by the current data display function of Subaru Select Monitor because no key illumination is available.) • Key illumination does not blink with ignition switch turned to ON and go off with door closed. (Models without the keyless access with push button start system) • Be sure to register immobilizer if body integrated unit is replaced with a new part. (Models without the keyless access with push button start system) • Make a registration of immobilizer when the parts related to immobilizer have been replaced. Refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume. 1. On «Start» display, select «Diagnosis». 2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed». 3. On «Main Menu» display, select «Each System». 4. On «Select System» display, select «Body Control» and then select «Enter». 5. On «Select Function» display, select «Customize». 6. Change the setting to the contents saved at confirmation of current setting. CAUTION: • To perform normal operation of vehicle and diagnosis, above settings must match the actual vehicle equipment. • When the body integrated unit is new or in Factory mode, the key illumination blinks, and user customizing is incomplete. Check the user customizing settings. (For models with keyless access with push button start system, the room light illuminates.) • Be sure not to change Factory initial setting except when installing a new body integrated unit. NOTE: “Factory” mode: • Body integrated unit has not been set yet. For model without keyless access with push button start system, it can be recognized by key ring illumination blinking with ignition switch turned to ON. For model with keyless access with push button start system, it can be recognized by room light, map light and luggage room light blinking with ignition switch turned to ON. • All replacement body integrated units are set to “Factory” mode. When replacing a body integrated unit, be sure to perform the registration operation. “Market” mode: • Each settings have been set. For model without keyless access with push button start system, it can be recognized by key ring illumination coming on in concocting with room light and going off with ignition switch turned to ON. For model with keyless access with push button start system, it can be recognized by room light, map light and luggage room light not blinking with ignition switch turned to ON. 7. Perform the Factory initial setting. On the «Customize» display screen of Subaru Select Monitor, select the «Factory initial setting». 8. Change the mode from Factory to Market. 9. Turn the ignition switch to OFF to settle the setting. 10. Change the system selection to «Immobilizer» on Subaru Select Monitor, and perform registration of immobilizer. (Models without the keyless access with push button start system) 11. Follow the procedure of the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume. (Models without the keyless access with push button start system) 12. For vehicles with remote engine starter, refer to “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume and perform registration of the remote engine starter. (Models without the keyless access with push button start system) 13. Perform the User Customizing. User Customizing > OPERATION NOTE: For detailed operation procedures, refer to “PC application help for Subaru Select Monitor”. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Read diagnostic trouble code (dtc) operation
1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. ...
Subaru select monitor operation
• For detailed operation procedures, refer to “Application help”.• When communication with Subaru Select Monitor is not possible, perform “COMMUNICATION FOR INITIALIZING ...
Other materials:
Maintenance mode
1. BRAKE MAINTENANCE MODENOTE:For brake maintenance mode, refer to “PARKING BRAKE” section. Parking Brake System > OPERATION2. VDCCM PARAMETER READING1. Perform reading of parameter.(1) Connect the Subaru Select Monitor to data link connector.NOTE:For detailed operation procedures, refe ...
